Essential cookies keep Rooutiq working. Optional analytics requires your permission. Privacy Policy

Enterprise security, built in.

Rooutiq separates permissions from operational approval. Ask for current control evidence and deployment-specific security status.

Learn about our security
Light / Medium Duty (OBD-II)5.3L V8 · 6.6L Duramax

GMC Fault Codes

Fleet Repair Costs & Prevention Guide

GMC Sierra and Savana fleet fault codes — OBD-II codes with average repair costs for commercial and fleet use.

34
Codes tracked
4
Critical severity
1.4d
Avg downtime
$26k
Combined repair pool

GMC Fault Codes (34)

Sorted by severity · Click any code for full repair cost breakdown

P0300CriticalEngine

Random/Multiple Cylinder Misfire

Multiple cylinders are misfiring simultaneously. Caused by worn spark plugs, failed ignition coils, fuel injector failure, or low compression.

P0016CriticalEngine

Crankshaft/Camshaft Position Correlation (Bank 1, Sensor A)

Timing chain/belt misalignment or VVT solenoid issue. Indicates possible timing chain failure.

P0017CriticalEngine

Crankshaft/Camshaft Position Correlation (Bank 1, Sensor B)

Exhaust camshaft timing misalignment on Bank 1. Similar to P0016 but on the exhaust cam.

P0339CriticalEngine

Crankshaft Position Sensor Circuit Intermittent

Intermittent crank position sensor signal loss. Engine may stall randomly with no warning.

P0303HighEngine

Cylinder 3 Misfire Detected

Cylinder 3 misfiring. Common on V6/V8 engines where cylinder 3 is prone to coil failure due to heat.

P0305HighEngine

Cylinder 5 Misfire Detected

Cylinder 5 misfiring. Most common on V8 engines — Bank 2, cylinder 5 coil and plug.

P0306HighEngine

Cylinder 6 Misfire Detected

Cylinder 6 misfiring. Often the last cylinder before the exhaust manifold — highest heat exposure for coils.

P0308HighEngine

Cylinder 8 Misfire Detected

Cylinder 8 misfiring. Rear-most cylinder in a V8 — often coil or plug but can indicate injector issues.

P0014HighEngine

B Camshaft Position Timing Over-Advanced (Bank 1)

Exhaust camshaft on Bank 1 over-advanced beyond commanded position. VVT solenoid or cam phaser fault.

P0521HighLubrication

Engine Oil Pressure Sensor Range/Performance

Oil pressure sensor reading out of expected range. Can indicate real low pressure or a failed sensor — must be verified mechanically.

P0670HighEngine (Diesel)

Glow Plug Module Control Circuit

Glow plug module has lost communication or failed. Critical for cold diesel starts below 40°F.

C0201HighBrakes/ABS

ABS Enable Relay Coil Circuit Open

ABS enable relay coil circuit is open — ABS cannot be energized. System fails safe with ABS disabled.

C0265HighBrakes/ABS

EBCM Relay Circuit Active

Electronic Brake Control Module relay fault. ABS and stability control offline.

P0307HighEngine

Cylinder 7 Misfire Detected

Cylinder 7 misfiring. Common on V8 engines — Bank 2, cylinder 7 coil failure is frequent after 100k miles.

P0316HighEngine

Misfire Detected on Startup (First 1000 Revolutions)

Misfire occurs on startup before catalytic converter reaches operating temperature. Catalyst damage accumulates fast.

P0024HighEngine

B Camshaft Position Timing Over-Advanced (Bank 2)

Exhaust camshaft on Bank 2 over-advanced beyond commanded position. Same failure mode as P0014 on opposite bank.

P0357HighEngine

Ignition Coil G Primary/Secondary Circuit

Coil G fault — cylinder 7 on V8 applications.

P0358HighEngine

Ignition Coil H Primary/Secondary Circuit

Coil H fault — cylinder 8, the last cylinder in a V8. Common failure point at high mileage.

DMAX-P0087HighFuel System (Duramax)

Duramax 6.6L LML/LGH Fuel Rail Pressure Low

Duramax 6.6L fuel rail pressure below minimum. CP4.2 high-pressure pump failure is the primary cause and is a known issue on LML engines.

DMAX-P2563HighTurbocharger (Duramax)

Duramax Turbocharger Boost Control Position Sensor

Duramax VGT turbocharger actuator position sensor fault — ECM loses feedback on vane position.

DMAX-B20HighFuel System (Duramax)

Duramax 6.6L — Injector Return Flow Excessive

Duramax injector return flow exceeds acceptable limit — one or more injectors leaking internally.

P0171MediumFuel System

System Too Lean (Bank 1)

Engine running lean — too much air, not enough fuel. MAF sensor, vacuum leak, weak fuel pump, or clogged injectors.

P0138MediumExhaust

O2 Sensor Circuit High Voltage (Bank 1, Sensor 2)

Downstream O2 sensor stuck at rich signal. Failed sensor or contaminated by oil or coolant.

P0411MediumEmissions

Secondary Air Injection System Incorrect Flow

AIR pump system not providing expected airflow during cold start. AIR pump failure, check valve failure, or solenoid fault.

B1325MediumBody Electrical

Control Module Power Circuit Low

Body control module power supply is low. Battery, fuse, or wiring issue preventing BCM from operating correctly.

P0196MediumLubrication

Engine Oil Temperature Sensor Range/Performance

Engine oil temperature sensor reading out of expected range for current coolant temp and run conditions.

P0197MediumLubrication

Engine Oil Temperature Sensor Circuit Low

Oil temperature sensor circuit shorted low — ECM assumes oil is very hot and may disable features.

P2453MediumAftertreatment (Diesel)

Diesel Particulate Filter Pressure Sensor A Circuit Range/Performance

DPF differential pressure sensor giving erratic or out-of-range readings. ECM cannot accurately monitor DPF loading.

P0473MediumExhaust

Exhaust Pressure Sensor High Input

Exhaust backpressure sensor reading above expected range — diesel engines with variable exhaust backpressure valves.

P0325MediumEngine

Knock Sensor 1 Circuit Malfunction (Bank 1)

Knock sensor circuit failure on Bank 1. ECM cannot detect engine knock — defaults to conservative ignition timing.

P0330MediumEngine

Knock Sensor 2 Circuit Malfunction (Bank 2)

Bank 2 knock sensor circuit failure. Bank 2 ignition timing retarded to maximum conservative table.

P3400MediumEngine (AFM)

Cylinder Deactivation System Bank 1

GM Active Fuel Management (AFM) cylinder deactivation system fault on Bank 1. Lifter collapse is the most common cause.

P3401MediumEngine (AFM)

Cylinder 1 Deactivation Solenoid Control Circuit

Cylinder 1 AFM deactivation solenoid circuit fault. Cylinder 1 cannot be deactivated or reactivated on command.

P3425MediumEngine (AFM)

Cylinder 4 Deactivation Solenoid Control Circuit

Cylinder 4 AFM solenoid circuit fault on GM 5.3L engines.

GMC Fleet Fault Code Overview

GMC vehicles equipped with 5.3L V8, 6.6L Duramax, 6.2L V8 engines generate OBD-II fault codes that vary in severity from routine maintenance reminders to engine-threatening conditions.

For light and medium duty commercial fleets running GMC vehicles, the most critical codes involve engine misfires, transmission faults, and fuel system degradation. These codes can result in costly roadside breakdowns if not caught early.

Rooutiq can use supported telematics and maintenance evidence from GMC fleet vehicles as inputs to a governed Fleet Situation, keeping source, timing, ownership, authority, and downstream repair state visible together.

Fault Codes by Vehicle Make