Essential cookies keep Rooutiq working. Optional analytics requires your permission. Privacy Policy

Enterprise security, built in.

Rooutiq separates permissions from operational approval. Ask for current control evidence and deployment-specific security status.

Learn about our security
Light / Medium Duty (OBD-II)5.7L V8 · 2.7L 4-cyl

Toyota Fault Codes

Fleet Repair Costs & Prevention Guide

Toyota Tundra and Tacoma fleet fault codes — OBD-II codes with average repair costs and downtime data.

78
Codes tracked
5
Critical severity
1.3d
Avg downtime
$46k
Combined repair pool

Toyota Fault Codes (78)

Sorted by severity · Click any code for full repair cost breakdown

P0300CriticalEngine

Random/Multiple Cylinder Misfire

Multiple cylinders are misfiring simultaneously. Caused by worn spark plugs, failed ignition coils, fuel injector failure, or low compression.

P0335CriticalEngine

Crankshaft Position Sensor A Circuit Malfunction

CKP sensor circuit has failed or has no signal. Engine will not start without crank position data.

P0601CriticalEngine Control

Internal Control Module Memory Check Sum Error

PCM has detected a memory checksum failure — calibration data may be corrupted.

B2799CriticalSecurity / Immobilizer

Engine Immobilizer — No Transponder Signal

Immobilizer cannot read key transponder. Vehicle will crank but not start.

P0336CriticalEngine

Crankshaft Position Sensor A Circuit Range/Performance

CKP sensor signal is present but erratic or out of expected range. Often intermittent stall or rough running before no-start.

P0301HighEngine

Cylinder 1 Misfire Detected

Cylinder 1 specifically is misfiring. Easier to diagnose than P0300 — isolates to one coil, plug, injector, or compression issue.

P0303HighEngine

Cylinder 3 Misfire Detected

Cylinder 3 misfiring. Common on V6/V8 engines where cylinder 3 is prone to coil failure due to heat.

P0304HighEngine

Cylinder 4 Misfire Detected

Cylinder 4 misfiring. Common on 4-cylinder engines where cylinder 4 runs hotter.

P0305HighEngine

Cylinder 5 Misfire Detected

Cylinder 5 misfiring. Most common on V8 engines — Bank 2, cylinder 5 coil and plug.

P0306HighEngine

Cylinder 6 Misfire Detected

Cylinder 6 misfiring. Often the last cylinder before the exhaust manifold — highest heat exposure for coils.

P0308HighEngine

Cylinder 8 Misfire Detected

Cylinder 8 misfiring. Rear-most cylinder in a V8 — often coil or plug but can indicate injector issues.

P0011HighEngine

A Camshaft Position Timing Over-Advanced (Bank 1)

VVT system fault — camshaft timing is advanced beyond spec. Stuck VVT solenoid or low oil pressure.

P0012HighEngine

A Camshaft Position Timing Over-Retarded (Bank 1)

Camshaft timing retarded beyond spec on Bank 1. VVT solenoid stuck in retard position or cam phaser wear.

P0014HighEngine

B Camshaft Position Timing Over-Advanced (Bank 1)

Exhaust camshaft on Bank 1 over-advanced beyond commanded position. VVT solenoid or cam phaser fault.

P0021HighEngine

A Camshaft Position Timing Over-Advanced (Bank 2)

Bank 2 intake camshaft over-advanced. Same as P0011 but affects the second bank of a V-engine.

P0340HighEngine

Camshaft Position Sensor Circuit Malfunction (Bank 1)

Cam position sensor circuit failure on Bank 1. Affects VVT operation and can prevent starting.

P0420HighExhaust

Catalyst System Efficiency Below Threshold (Bank 1)

Catalytic converter efficiency is below EPA threshold. O2 sensors show insufficient conversion of hydrocarbons.

P0430HighExhaust

Catalyst System Efficiency Below Threshold (Bank 2)

Bank 2 catalyst efficiency below threshold. Affects V6 and V8 engines — both banks can fail.

P0234HighTurbocharger

Turbocharger Overboost Condition

Boost pressure exceeding safe limit. Wastegate stuck closed, boost solenoid failure, or boost sensor fault.

P0299HighTurbocharger

Turbocharger Underboost Condition

Boost pressure below minimum. Worn turbo, boost leak, stuck-open wastegate, or VGT fault.

P0521HighLubrication

Engine Oil Pressure Sensor Range/Performance

Oil pressure sensor reading out of expected range. Can indicate real low pressure or a failed sensor — must be verified mechanically.

C0040HighBrakes/ABS

Right Front Wheel Speed Sensor Circuit

ABS wheel speed sensor fault on right front. Disables ABS system.

P0307HighEngine

Cylinder 7 Misfire Detected

Cylinder 7 misfiring. Common on V8 engines — Bank 2, cylinder 7 coil failure is frequent after 100k miles.

P0013HighEngine

B Camshaft Position — Actuator Circuit (Bank 1)

Exhaust VVT oil control solenoid circuit fault on Bank 1. Solenoid cannot command exhaust cam timing.

P0022HighEngine

A Camshaft Position Timing Over-Retarded (Bank 2)

Bank 2 intake cam timing retarded beyond commanded position. Oil pressure or VVT solenoid issue on Bank 2.

P0023HighEngine

B Camshaft Position — Actuator Circuit (Bank 2)

Bank 2 exhaust VVT oil control solenoid circuit fault. Exhaust cam on Bank 2 locked at default timing.

P0024HighEngine

B Camshaft Position Timing Over-Advanced (Bank 2)

Exhaust camshaft on Bank 2 over-advanced beyond commanded position. Same failure mode as P0014 on opposite bank.

P0354HighEngine

Ignition Coil D Primary/Secondary Circuit

Coil D circuit fault — affects cylinder 4 on most COP applications.

P0355HighEngine

Ignition Coil E Primary/Secondary Circuit

Coil E circuit fault — cylinder 5 on V8 and cylinder 5 on some V6 configurations.

P0356HighEngine

Ignition Coil F Primary/Secondary Circuit

Coil F circuit fault — cylinder 6. Rear cylinders on V8 engines experience higher heat and coil failure rates.

P0358HighEngine

Ignition Coil H Primary/Secondary Circuit

Coil H fault — cylinder 8, the last cylinder in a V8. Common failure point at high mileage.

P0120HighEngine

Throttle/Pedal Position Sensor A Circuit Malfunction

Primary TPS circuit failure on a drive-by-wire system. ECM enters failsafe with limited throttle response.

P0121HighEngine

Throttle/Pedal Position Sensor A Range/Performance

TPS A output is out of expected range. Not a full failure but erratic — ECM may enter failsafe.

P0123HighEngine

Throttle/Pedal Position Sensor A Circuit High Input

TPS A signal above maximum. Shorted signal wire or failed sensor.

P2100HighEngine

Throttle Actuator Control Motor Circuit Open

Electronic throttle body actuator motor has an open circuit — motor cannot respond to commands.

P0730HighTransmission

Incorrect Gear Ratio

Transmission achieving incorrect gear ratio for commanded gear. Indicates internal clutch pack slippage or failure.

P0731HighTransmission

Gear 1 Incorrect Ratio

First gear ratio is incorrect — clutch packs not fully engaging or slipping. Indicates transmission wear.

P0750HighTransmission

Shift Solenoid A Malfunction

Shift solenoid A circuit or mechanical failure. TCM cannot execute gear changes using solenoid A.

P0755HighTransmission

Shift Solenoid B Malfunction

Shift solenoid B circuit or mechanical failure. Same failure mode as P0750 on a different solenoid channel.

C0041HighBrakes/ABS

Right Front Wheel Speed Sensor Circuit Range/Performance

Right front wheel speed sensor erratic signal. Tone ring damage or bearing play affecting sensor gap.

B0057HighSafety (SRS)

Side Impact Sensor — Left Front B-Pillar Circuit Fault

Left front side impact crash sensor circuit fault. Side curtain and seat airbags may not deploy in a side impact.

P003AHighTurbocharger

Turbocharger/Supercharger Boost Control A Position Exceeded

Turbo actuator exceeded commanded position limit — wastegate or VGT actuator issue.

P0341HighEngine

Camshaft Position Sensor Circuit Range/Performance (Bank 1)

CMP sensor on Bank 1 has signal but is erratic or implausible. VVT system affected.

P0344HighEngine

Camshaft Position Sensor Circuit Intermittent (Bank 1)

Bank 1 CMP sensor dropping out intermittently. Engine may stumble or stall without warning.

P0200HighFuel System

Fuel Injector Circuit Malfunction

Generic fuel injector circuit fault — one or more injectors has a circuit problem. Misfires and rough running result.

P0201HighFuel System

Injector Circuit Malfunction — Cylinder 1

Fuel injector circuit fault on cylinder 1. Injector not firing — misfire on cylinder 1 results.

P0202HighFuel System

Injector Circuit Malfunction — Cylinder 2

Fuel injector circuit fault on cylinder 2 — same failure mode as P0201.

P0204HighFuel System

Injector Circuit Malfunction — Cylinder 4

Cylinder 4 fuel injector circuit fault.

P0270HighFuel System

Injector Circuit Low — Cylinder 4

Cylinder 4 injector circuit shorted low — wiring grounded or injector coil short circuit.

C0600HighSteering

Steering Angle Sensor Fault

Steering angle sensor circuit fault or data implausible. Stability control system cannot function correctly without steering angle data.

P0175MediumFuel System

System Too Rich (Bank 2)

Bank 2 running rich. Often caused by a leaking injector or faulty O2 sensor on that bank.

P0131MediumFuel System

O2 Sensor Circuit Low Voltage (Bank 1, Sensor 1)

Upstream O2 sensor stuck at lean signal. Sensor contaminated, failed, or exhaust leak near sensor.

P0133MediumFuel System

O2 Sensor Slow Response (Bank 1, Sensor 1)

Upstream O2 sensor is responding too slowly. Sensor nearing end-of-life — element degraded.

P0101MediumEngine

Mass Air Flow Sensor Range/Performance

MAF sensor readings outside expected parameters. Dirty sensor, intake leak, or failed MAF.

P0102MediumEngine

Mass Air Flow Sensor Circuit Low Input

MAF sensor output voltage below minimum. Open circuit, failed sensor, or air filter housing leak bypassing sensor.

P2279MediumAir Intake

Intake Air System Leak

ECM has detected an intake air system leak (unmetered air) from MAF and O2 sensor correlation.

P0118MediumCooling

Engine Coolant Temperature Sensor Circuit High

Coolant temp sensor signal is above maximum. Open circuit or failed sensor causing ECM to assume extreme cold.

P0128MediumCooling

Coolant Temperature Below Thermostat Regulating Temperature

Engine coolant not reaching normal operating temperature. Almost always a failed thermostat stuck open.

P0138MediumExhaust

O2 Sensor Circuit High Voltage (Bank 1, Sensor 2)

Downstream O2 sensor stuck at rich signal. Failed sensor or contaminated by oil or coolant.

P2096MediumExhaust

Post Catalyst Fuel Trim System Too Lean (Bank 1)

Post-catalyst O2 sensor indicating lean downstream — exhaust gas downstream is lean, suggesting the catalyst is consuming too much oxygen.

P0132MediumFuel System

O2 Sensor Circuit High Voltage (Bank 1, Sensor 1)

Upstream O2 sensor stuck high — indicating a rich condition persistently. Sensor fouled or failed.

P0134MediumFuel System

O2 Sensor Circuit No Activity (Bank 1, Sensor 1)

Upstream O2 sensor showing no switching activity. Sensor dead, heating element failed, or no exhaust gas reaching sensor.

P0136MediumExhaust

O2 Sensor Circuit Malfunction (Bank 1, Sensor 2)

Downstream O2 sensor circuit failure. Cannot monitor catalyst efficiency — P0420 soon to follow.

P0137MediumExhaust

O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2)

Downstream O2 sensor stuck at lean signal. Sensor failed or exhaust leak downstream of catalyst.

P0119MediumCooling

Engine Coolant Temperature Sensor Intermittent

Intermittent coolant temperature sensor signal. ECM is detecting erratic readings from ECT sensor.

P0325MediumEngine

Knock Sensor 1 Circuit Malfunction (Bank 1)

Knock sensor circuit failure on Bank 1. ECM cannot detect engine knock — defaults to conservative ignition timing.

P0326MediumEngine

Knock Sensor 1 Circuit Range/Performance (Bank 1)

Knock sensor output out of expected range — either too quiet or producing false knock signals.

P0330MediumEngine

Knock Sensor 2 Circuit Malfunction (Bank 2)

Bank 2 knock sensor circuit failure. Bank 2 ignition timing retarded to maximum conservative table.

P0031LowFuel System

HO2S Heater Control Circuit Low (Bank 1, Sensor 1)

Upstream O2 sensor heater circuit is drawing too little current. Heater element failure or circuit fault.

P0141LowExhaust

O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 2)

Downstream O2 sensor heater circuit fault. Sensor heater failure means slow warmup and inaccurate readings during cold start.

P0441LowEVAP

Evaporative Emission Control System Incorrect Purge Flow

EVAP purge flow doesn't match expected. Purge valve stuck open or closed.

P0442LowEVAP

Evaporative Emission System Small Leak

Small EVAP leak detected. Most commonly a loose or cracked gas cap, but can be a faulty purge valve.

P0446LowEVAP

Evaporative Emission Control System Vent Control Circuit

EVAP vent solenoid circuit failure. System cannot purge vapor properly.

P0030LowFuel System

HO2S Heater Control Circuit (Bank 1, Sensor 1)

Upstream O2 sensor heater control circuit fault — open or shorted heater element.

P0135LowFuel System

O2 Sensor Heater Circuit Malfunction (Bank 1, Sensor 1)

Upstream O2 sensor heater circuit failure. Cold-start emissions increase significantly.

U0164LowCAN Bus / Network

Lost Communication with HVAC Control Module

HVAC control module lost CAN communication. Climate control defaults to a fixed mode — heat or cold depending on default.

U0184LowCAN Bus / Network

Lost Communication with Radio

Infotainment/radio module lost CAN communication. Loss of radio, backup camera, and navigation in modern fleet vehicles.

P0564LowElectrical

Cruise Control Multi-Function Input A Circuit

Cruise control switch circuit fault — cruise control inoperable. Driver complaint on highway fleet vehicles.

Toyota Fleet Fault Code Overview

Toyota vehicles equipped with 5.7L V8, 2.7L 4-cyl, 2GR-FE V6 engines generate OBD-II fault codes that vary in severity from routine maintenance reminders to engine-threatening conditions.

For light and medium duty commercial fleets running Toyota vehicles, the most critical codes involve engine misfires, transmission faults, and fuel system degradation. These codes can result in costly roadside breakdowns if not caught early.

Rooutiq can use supported telematics and maintenance evidence from Toyota fleet vehicles as inputs to a governed Fleet Situation, keeping source, timing, ownership, authority, and downstream repair state visible together.

Fault Codes by Vehicle Make